Send an Inquiry

Digital Multifunction Protective Relay ASL-591H

Overview of Digital Multifunction Protective Relay

The ASL-591H digital multifunction protective relay protects 10kV and below RMU/GIS lines and 380V distribution room lines.

ANSI

50/51/49/51N/63

Communication Mode:Optional: RS-485, CAN bus, Ethernet, IEC 60870-5-103 (IEC-103)

Download datasheet (PDF)

Send your requirements, we will quote for you within 12 hours​
MOQ: 1 setLead time: 7-15 working daysPayment: T/T, L/C, Western Union, PayPalWarranty: 12 monthsTrade terms: EXW, FOB, CIF, DDUCertification: CEDifferent rating, protocol or mounting: send the specification and we confirm before you order.

Description

What is an ASL-591H digital multifunction protective relay?

The ASL-591H is a feeder protection relay that combines overcurrent, earth fault, negative sequence, under and over voltage, frequency and breaker failure functions in one chassis, so a single device covers a bay that would otherwise need three. The practical value is in the fault recording and the metering it carries alongside the protection: when a feeder trips, the record already holds the currents, the element that operated and the timing, which is what a coordination review needs. The relay is configured through a front port or over the station LAN, and the setting file can be exported and compared between units so a fleet stays consistent. Typical duty is a 10 kV or 35 kV outgoing feeder, a plant distribution board or a capacitor and reactor bay. IEC 60255-1 defines the performance. Configuration review at order; quotation within 12 hours, MOQ 1, 7-15 working days.

Overview of Digital Multifunction Protective Relay

  • The ASL-591H Microprocessor-Based Comprehensive Protection Device, a digital multifunction protective relay, is suitable for the comprehensive protection of 10 kV and below incoming and outgoing lines in ring main units and gas-insulated switchgear, as well as 380 V low-voltage incoming and outgoing lines in distribution rooms.
Multifunction Protective Relay

Features of Numerical Protection Relay

  • This multifunction protection relay is suitable for plant service transformers, power supply feeders and bus tie protection at 10 kV and below. It supports AC/DC 220 V and DC 110 V power supplies (24 V/48 V available on request). Featuring a compact design, it is easy for instrument room installation.

Functions of Digital Multifunction Protection Relays

  • Two-stage overcurrent protection (instantaneous current tripping & definite-time overcurrent), each stage can be independently enabled or disabled;
  • Overload protection: output configurable for tripping or alarm;
  • Zero-sequence overcurrent protection: output configurable for tripping or alarm;
  • Inverse-time overcurrent protection: fixed output for tripping;
  • Non-electrical protection: heavy gas tripping (transformer door interlock), over-temperature tripping, light gas alarm, over-temperature alarm, etc.

Event Logging Function of Digital Multifunction Protection Relay

  • The log records events including protection trip events, alarm events, and device self-test failures;
  • It records the type and time of protection trip events, as well as the type and time of device self-test failures.

Numerical Protective Relays – Communication Functions

  • Upload real-time data, including measurement data, fault alarm signals, and protection settings.
  • Receive control commands from higher-level systems.

Communication Interface

  • This device provides a high-speed, reliable RS-485 interface for external communication. It supports the standard MODBUS protocol.

Rated DC Specifications

  • Voltage: 220 V, 110 V; DC voltage ripple factor: ≤2%; voltage fluctuation: 80–115% of rated voltage

Rated AC Specifications

  • Rated AC current In: 5 A, 1 A;
  • The AC power waveform is sinusoidal, with a distortion factor not exceeding 2%;
  • Frequency fn: 50 Hz (60 Hz option available; specify when ordering), with a tolerance of ±0.5%.

Dimensions of Numerical Protection Relays

digital multifunction protective relay

Multifunctional Protection Relay Setting Sheet

No.NameRangeStepRemarks
1Stage 1 Protection Setting (Instantaneous Current Trip)
1.1Stage 1 Protection Enable1/0–Stage 1 protection: Enable(1) / Disable(0)
1.2Stage 1 Time Delay0~120.00s0.01s
1.3Stage 1 Setting Value0.40~99.99A0.01A
2Stage 2 Protection Setting (Definite-time Overcurrent)
2.1Stage 2 Protection Enable1/0–Stage 2 protection: Enable(1) / Disable(0)
2.2Stage 2 Time Delay0~120.00s0.01s
2.3Stage 2 Setting Value0.40~99.99A0.01A
3Overload Setting
3.1Overload Protection Enable1/0–Overload protection: Enable(1) / Disable(0)
3.2Overload Trip Mode1/0–Overload: Trip(1) / Alarm(0)
3.3Overload Time T0~120.00s0.01s
3.4Overload Current I0.40~99.99A0.01A
4Zero-sequence Overcurrent Setting
4.1Zero-sequence Overcurrent Enable1/0–Zero-sequence overcurrent protection: Enable(1) / Disable(0)
4.2Zero-sequence Overcurrent Trip Mode1/0–Zero-sequence overcurrent: Trip(1) / Alarm(0)
4.3Zero-sequence Time Delay0~120.00s0.01s
4.4Zero-sequence Setting Value0.5~99.99A0.01A
5Inverse-time Overcurrent Setting
5.1Inverse-time Overcurrent Enable1/0–Inverse-time overcurrent protection: Enable(1) / Disable(0)
5.2Inverse-time Time Constant T0.1~120.00s0.01sTime constant of inverse-time overcurrent protection
5.3Inverse-time Current Setting I1~10A0.01ASetting value of inverse-time overcurrent protection
6Non-electrical Protection Setting
6.1Non-electrical Protection 1 Enable1/0–Non-electrical protection 1: Enable(1) / Disable(0)
6.2Non-electrical Protection 1 Trip Mode1/0–Non-electrical protection 1: Trip(1) / Alarm(0)
6.3Non-electrical Protection 2 Enable1/0–Non-electrical protection 2: Enable(1) / Disable(0)
6.4Non-electrical Protection 2 Trip Mode1/0–Non-electrical protection 2: Trip(1) / Alarm(0)
6.5Non-electrical Protection 3 Enable1/0–Non-electrical protection 3: Enable(1) / Disable(0)
6.6Non-electrical Protection 3 Trip Mode1/0–Non-electrical protection 3: Trip(1) / Alarm(0)
6.7Non-electrical Protection 4 Enable1/0–Non-electrical protection 4: Enable(1) / Disable(0)
6.8Non-electrical Protection 4 Trip Mode1/0–Non-electrical protection 4: Trip(1) / Alarm(0)
6.9Non-electrical 1 Time Delay0.1~120.00s0.01s
6.10Non-electrical 2 Time Delay0.1~120.00s0.01s
6.11Non-electrical 3 Time Delay0.1~120.00s0.01s
6.12Non-electrical 4 Time Delay0.1~120.00s0.01s
6.13Non-electrical Parameter Value0000-FFFF–
7General Setting
7.1Three-element Wiring Enable1/0–Three-element wiring: Enable(1) / Disable(0)
7.2Current Transformation Ratio0-99991

FAQ

Q:How are comprehensive protection relays typically installed and used, and what types of equipment can they protect?

A:Compact comprehensive protection devices are suitable for installation in ring main units and high-voltage switchgear. With control in numerical protection relay integrated, they provide complete protection for feeders, feeder terminals, distribution transformers and small motors.

Q What is this relay?

A microprocessor-based IED integrating protection, measurement, control, fault recording and communication, replacing multiple discrete electromagnetic relays for power system protection.

Q Core advantages vs traditional relays

All-in-one compact design, high precision settings, built-in fault waveform recording, remote communication, continuous self-diagnosis and no mechanical drift.

Q Common built-in protection elements

50/51 overcurrent, 50N/51N earth fault, 67 directional overcurrent, 27/59 undervoltage/overvoltage, 46 negative sequence, 32 reverse power, 87 differential, 81 frequency protection, breaker failure & trip circuit supervision.

Q Typical application objects

10/35kV feeders, distribution transformers, medium-voltage motors, capacitor banks, bus tie & incoming cabinet auto transfer logic.

Q Required input signals

Three-phase CT current, three-phase PT voltage, zero-sequence current; digital inputs for breaker status & interlock signals, digital outputs for trip, close and alarm.

Q Built-in circuit monitoring

Supports PT fuse failure and CT broken wire detection, automatically alarms and blocks relevant protection to prevent false tripping.

Q Ways to configure parameters

Local panel operation, PC software via USB/485, or remote download through SCADA system.

Q Protection coordination principle

Adopt definite/inverse time curves with time & current grading to ensure selective tripping between upstream and downstream equipment.

Q Supported protocols

Modbus, IEC 103/104, DNP3, IEC 61850 with GOOSE for smart substation interlocking.

Q Key data recording

Real-time electrical measurements, event logs, fault oscillography and action records for post-fault analysis.

Q False tripping main causes

CT polarity/ratio error, PT abnormality, over-sensitive settings, electromagnetic interference or unremoved blocking signals.

Q Protection fails to trip

Loss of control power, CT secondary open/short circuit, excessively high pickup values, broken trip circuit or external interlock locking.

Q Self-check alarm

Hardware failure of power supply, mainboard or memory; replace the unit or send for factory repair.

Q Necessary commissioning items

CT/PT polarity check, secondary injection test, DI/DO loop verification, communication debugging and setting file backup.

Q Routine maintenance

Monthly status check; annual terminal tightening and dust cleaning; full function inspection during major overhaul every 4~6 years.

Q Optional extra features

Auto-reclosing, cold load pickup, password permission lock for parameter modification, IEC 61850 GOOSE peer-to-peer intertrip.

Q Usage value

Reduces cabinet space, wiring workload and fault points, widely adopted in new distribution substations and industrial power distribution systems.

Q How do I place an order?

Send your specification through the contact form, by email to sale@relayprotect.com or on WhatsApp. We check the rating, the protocol and the wiring against your application, confirm the model, and return a quotation. No account or registration is needed.

Q What is the minimum order quantity?

The minimum order quantity is one unit. A single unit can be ordered for evaluation or for a pilot installation, and project quantities are quoted separately.

Q What is the lead time?

Standard models ship in 7 to 15 working days after the order is confirmed and payment is received. Custom ratings, protocols or mounting arrangements are confirmed in writing before the order is placed, so the delivery date is known in advance.

Q Which payment methods and trade terms do you accept?

Payment by T/T, L/C, Western Union or PayPal. Trade terms are EXW, FOB, CIF and DDU. Every relay carries a 12-month warranty.


Need pricing, a datasheet or a wiring drawing?

Tell us your application – rated voltage, CT/VT ratios and the protection functions you need – and we will send a quotation with the matching model. Free technical guidance, parameter setting and commissioning support included.

MOQ 1 unit for samples | Bulk orders ship in 7-15 working days | 12-month warranty | EXW, FOB, CIF, DDU | Payment by T/T, L/C, Western Union or PayPal. New to ordering? See how to order – process, MOQ and lead time.

Reviews

There are no reviews yet.

Be the first to review “Digital Multifunction Protective Relay ASL-591H”

Your email address will not be published. Required fields are marked *

High Quality

Stable performance, reliable design, ensuring safe operation for power system protection and grid stability.

Fast Delivery

Timely delivery to support your urgent orders and project schedules efficiently and professionally at any time.

Best Warranty

Professional Warranty: Reliable after-sales support for stable relay protection and long-term customer satisfaction.